Free Cisco 300-080 Exam Dumps – [Jan-2018 Dumps]

By | January 23, 2018

Success in Cisco Certified Network Professional Collaboration 300-080 exam with the all-inclusive Cisco 300-080 exam dumps preparation material is offered with money back guarantee so either you embrace the success or get your money back because your success is the central focus. 300-080 exam practice test software is designed in a way that it gives you a chance of getting a clear picture of whole syllabus, exam pattern, practice of exam in simulated real exam scenarios and more than all evaluation of your learning independently with self-assessment feature.

♥♥ 2018 NEW RECOMMEND 300-080 Exam Questions ♥♥

300-080 exam questions, 300-080 PDF dumps; 300-080 exam dumps:: https://www.dumpsschool.com/300-080-exam-dumps.html (157 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 300-080 Dumps Exam Questions and Answers:

Version: 10.0
Question: 21

Refer to the exhibit.

Assume a centralized Cisco Unified Communications Manager topology with the headquarters at RTP and remote located at the U.K. All route patterns are assigned a route list that contains a route group pointing to the local gateway. RTP route patterns use the RTP gateway, and U.K. route patterns use the U.K. gateway.
When a U.K. user logs into an RTP phone using the Cisco Extension Mobility feature and places an emergency call to 0000, which statement about the emergency call is true?

A. The call will match the U.K_Emergency route pattern partition and will egress at the RTP gateway.
B. The call will match the U.K_Emergency route pattern partition and will egress at the U.K. gateway.
C. The call will match the RTP_Emergency route pattern partition and will egress at the RTP gateway.
D. The call will match the RTP_Emergency route pattern partition and will egress at the U.K. gateway.
E. The call will fail.

Answer: B

Question: 22

Refer to the exhibit.

Local 10-digit dialing in the North American Numbering Plan to area code 456 is failing. Which two changes are needed to enable 10-digit dialing? (Choose two.)

A. Change dial peer 210 to destination-pattern 456…….
B. Change dial peer 210 to destination-pattern 9456…….
C. Change dial peer 210 to port 0/0/0:23.
D. Remove the command prefix 456 from dial peer 210.

Answer: B, C

Question: 23

You configured a Cisco ISR G2 as a SIP gateway, but the gateway does not show that it is registered with Cisco Unified Communications Manager. What is causing this issue?

A. Cisco Unified Communications Manager does not support SIP gateways.
B. The gateway does not have the UC license installed.
C. The gateway does not have Cisco Unified Border Element session licensing.
D. Cisco Unified Communications Manager does not show a SIP gateway as registered if it is not properly configured.
E. Cisco Unified Communications Manager never shows a SIP gateway as registered even when it is properly configured.
F. The Cisco ISR G2 cannot be a SIP gateway.

Answer: E

Question: 24

Which issue would cause an MGCP gateway to fail to register with Cisco Unified Communications Manager?

A. missing the configuration command isdn bind-l3 ccm-manager under the ISDN interface
B. mismatched domain name on the MGCP gateway and Cisco Unified Communications Manager gateway configuration
C. misconfigured route group in Cisco Unified Communications Manager
D. incorrect MGCP IP address specified in the gateway configuration in Cisco Unified Communications Manager

Answer: B

Question: 25

Endpoints are configured for both H.323 and SIP using the same URI and Cisco VCS settings, but the endpoints register only as H.323 endpoints. What is causing this issue?

A. A firewall is blocking all traffic from the endpoints to the Cisco VCS.
B. The Cisco VCS has no SIP domains configured.
C. The Cisco VCS is blocking the endpoints because of duplicate ID entries.
D. The endpoints do not have the SIP option key installed.
E. SIP does not work, because SIP is used for Cisco Unified Communications Manager registration only.

Answer: B

Question: 26

You are trying to register an H.323-based Cisco TelePresence system to Cisco Unified Communications Manager and a Cisco DX70 system to the Cisco VCS Control. Why do neither of the units want to register?

A. The H.323-based system needs an E164 number to register to Cisco Unified Communications Manager, and the Cisco DX70 needs to have the MAC address configured first on the Cisco VCS Control.
B. The H.323-based system needs to register to the Cisco VCS Control with an E.164 number, and the Cisco DX70 needs the TFTP address to register on the Cisco Unified Communications Manager.
C. Both systems need to register to the Cisco VCS Control, but the H.323-based system needs to have the gatekeeper setting set to “Direct.”
D. Both systems need to register to the Cisco Unified Communications Manager, as the Cisco VCS Control is used only for firewall traversal.
E. You need Cisco TelePresence Management Suite to register Cisco TelePresence systems.
F. You need Cisco TelePresence Server to register Cisco TelePresence systems.

Answer: B

New Updated 300-080 Exam Questions 300-080 PDF dumps 300-080 practice exam dumps: https://www.dumpsschool.com/300-080-exam-dumps.html